Page Comparison

Short Description

...

1. Anchor
   vrs1 vrs1

   Locating the Port Call to be Updated in Dataloy VMS
   As the Dataloy VMS schedule is not accessible to offline vessels, the system relies on information in the reported data to locate the correct port call - i.e. the vessel and the report date. Different rules apply depending on report type:
   1.  Arrival, Noon and In Port Report
      1.  Vessel reporting will search through port calls and locate the first port call where the departure date is after the report date.
         Note: Redelivery ports and the straits Torres, Bosporus and Maggelan are excluded.
   2. Departure Report
      1. Vessel reporting will search through port calls and locate the first port call where the departure date is after the report date. The system will choose this port call as the next arrival port.
      2. The vessel reporting will select the previous port call as the departure port. If Departure Fixed is set for this port, the system will move to the next port for both the departure and arrival ports. If Departure fixed is not set for the previous port, the vessel reporting will go backwards to the first port call where Departure Fixed is not set.
         Note: Redelivery ports and the straits Torres, Bosporus and Maggelan are excluded.
   3. Multiple Port Calls for the Same Port, Registered in Dataloy
      1. Rule for vessel report updating when there are multiple port calls to the same port after each other
         1. Arrival, Noon and In Port Report will update the first port call.

         2. Departure Report will update the last port call.

            Info
            ETA and ETB are set as fixed in the Dataloy VMS when the entered date is in the past. ETD is set as fixed - only for the Departure Report.

2. Anchor
   vrs2 vrs2

   Field Validation
   1. Grey check mark appears: Indicates field is mandatory.
   2. Green check mark appears: Indicates field is validated.
      
      
      
      

   3.  The Submit button activates once all fields are validated (i.e. have green check marks).
      
      

      Info
      Logical date check exists for ETA, ETB and ETD. A report will be invalid and impossible to send if the ETB is entered as a date preceding the ETA. Noon Reports: The Daily Net Fresh Water Consumption section allows for negative numbers. Note: Negative numbers indicates higher water production than consumption.

       
      Example of validated and not validated fields:
      
      
      

       

      
      

3. Anchor
   vrs3 vrs3

   Data from Previous Report
   Data from a previous report will appear in the Previous Report column. This previous value can be copied into the current report.
   Note: Cookies must be enabled for this function. 
    

   

    
   

   Anchor
   vrs4 vrs4

   Submit Report
   The Submit button activates once all fields are validated (i.e. have green check marks). Click to submit report. A pre-filled in e-mail will open in the the default mail client. DO NOT CHANGE THE CONTENTS OF THIS E-MAIL. It should be sent as is.
   Note: If the e-mail client automatically adds text to the mail body, for example a signature, DO NOT remove it. This type of addition is acceptable. Size of mail including mail headers is about 5kb.
   
   Example: 
   
   
   
   

4. Anchor
   vrs5 vrs5

   Receiveing Mail in Dataloy VRS
   Mail is checked by the server every 30 minutes.
   Note: During a test phase this interval is 15 minutes.
   
   

5. Anchor
   vrs6 vrs6

   Confirmation and Error Mail
   Once a report has been inserted in Dataloy VMS, an e-mail can be sent to the Voyage Operator. This e-mail contains an overview of the data submitted from the vessel in a readable format. Note: If a report fails to be inserted an e-mail will be sent to a fixed e-mail address. If  the VMS located the port call before the report failed an error e-mail will also be sent to the Voyage Operator.To enable mail to be sent to the Voyage Operator, an e-mail address must first be added on user level.
   
   Example:
   
   Vessel: Vessel 1
   Departure Port: BERGEN
   Report Date Local Time: Wed Oct 24 00:00:00 CEST 2012
   Departure Time: Fri Oct 26 22:00:00 CEST 2012
   Next Port: OSLO
   Estimated Time of Arrival: Fri Oct 26 03:00:00 CEST 2012
   etc..
   
   

6. Anchor
   vrs7 vrs7

   Failing Report
   Failing reports must be corrected and resent from the vessel (overview of ossible error messages: Vessel Report is Failing - Error Messages).

...

1. Anchor
   vrs8 vrs8

   Noon Report
   

   Noon Report	Dataloy VMS
   Vessel Name	Used to locate the port call in Dataloy VMS.
   Position latitude	Inserted to position report.
   Position Longitude	Inserted to position report.
   Next Port	When a port call is located based on vessel and report date, Dataloy VMS checks the reported port against the port in Dataloy VMS. If these do not match an e-mail will be sent to the operator and the report will not be inserted.
   Report Date Local Time	Used to locate the port call in Dataloy.
   Estimated Time of Arrival	Updates ETA.
   Estimated Time of Berting (Optional)	Updates ETB
   Estimated Time of Departure (Optional)	Updates ETD
   True Course	Inserted to position report.
   Distance Sailed Since Last Report	Inserted to position report.
   Hours in Service Since Last Report	Inserted to position report.
   Distance To Go	Inserted to position report.
   Speed Made Good	Inserted to position report.
   Wind Direction	Inserted to position report.
   Wind Force	Inserted to position report.
   Sea Direction	Inserted to position report.
   Sea State	Inserted to position report.
   Main Engine RPM Since Last Report	Inserted to position report.
   Daily Fuel Oil consumption	Inserted to position report.
   Daily Diesel Oil consumption	Inserted to position report.
   Daily Fuel Oil Low Sulphur consumption	Inserted to position report.
   Daily Diesel Oil Low Sulphur consumption	Inserted to position report.
   Daily Net Fresh Water consumption	Inserted to position report.
   Fuel Oil remaining on board	Inserted to position report.
   Diesel Oil remaining on board	Inserted to position report.
   Fuel Oil Low Sulphur remaining on board	Inserted to position report.
   Diesel Oil Low Sulphur remaining on board	Inserted to position report.
   Fresh Water remaining on board	Inserted to position report.
   Remark	Inserted as remark to position report.

    

2. Anchor
   vrs9 vrs9

   Arrival Report
   

   Arrival Report	Dataloy VMS
   Vessel Name	Used to locate the port call in Dataloy VMS.
   Port	When a port call is located based on vessel and report date, Dataloy VMS checks the reported port against the port in Dataloy VMS. If these do not match an e-mail will be sent to the operator and the report will not be inserted.
   Report Date Local Time	Used to locate the port call in Dataloy VMS.
   Time of Arrival	Updates Arrival.
   Time of Berthing (Estimated if anchoring)	Updates ETB.
   Estimated Time of Departure	Updates ETD.
   Total Distance Sailed Since Departure	Updates Miles.
   Hours in Service Since Last Report	Inserted to position report.
   Hours Stoppages Since Last Report	Updates days stoppages  (under the Perfomance tab in Booking and Operations).
   Speed Made Good Since Last Report	Inserted to position report.
   Draft Aft	Inserted to position report.
   Draft Forward	Inserted to position report.
   Daily Fuel Oil consumption	Inserted to position report.
   Daily Diesel Oil consumption	Inserted to position report.
   Daily Fuel Oil Low Sulphur consumption	Inserted to position report.
   Daily Diesel Oil Low Sulphur consumption	Inserted to position report.
   Daily Net Fresh Water consumption	Inserted to position report.
   Fuel Oil remaining on board	Updates Fuel Oil ROB arrival.
   Diesel Oil remaining on board	Updates Diesel Oil ROB arrival.
   Fuel Oil Low Sulphur remaining on board	Updates Fuel Oil Low Sulphur ROB arrival.
   Diesel Oil Low Sulphur remaining on board	Updates Diesel Oil Low Sulphur ROB arrival.
   Fresh Water remaining on board	Inserted to position report.
   Remark	Inserted as remark to position report.

    

3. Anchor
   vrs10 vrs10

   In Port Report

   In Port Report	Dataloy VMS
   Vessel Name	Used to locate the port call in Dataloy VMS.
   Port	When a port call is located based on vessel and report date, Dataloy VMS checks the reported port against the port in Dataloy VMS. If these do not match an e-mail will be sent to the operator and the report will not be inserted.
   Report Date Local Time	Used to locate the port call in Dataloy VMS.
   Estimated Time of Departure	Updates ETD.
   Hours in Service	Inserted to position report.
   Weather	Inserted to position report.
   Wind Direction	Inserted to position report.
   Average Wind Force	Inserted to position report.
   Remark	Inserted as remark to position report.

   
   

4. Anchor
   vrs11 vrs11

   Departure Report

   Departure Report	Dataloy VMS
   Vessel Name	Used to locate the port call in Dataloy VMS.
   Departure Port	When a port call is located based on vessel and report date, Dataloy VMS checks the reported port against the port in Dataloy VMS. If these do not match an e-mail will be sent to the operator and the report will not be inserted.
   Report Date Local Time	Used to locate the port call in Dataloy VMS.
   Departure Time	Updates Departure.
   Next Port	When a port call is located based on vessel and report date, Dataloy VMS checks the reported port against the port in Dataloy VMS. If these do not match an e-mail will be sent to the operator and the report will not be inserted.
   Estimated Time of Arrival	Updates ETA for next port call.
   Distance To Next Port	Inserted to position report.
   Draft Aft	Inserted to position report.
   Draft Forward	Inserted to position report.
   Fuel Oil remaining on board	Updates Fuel Oil ROB departure.
   Diesel Oil remaining on board	Updates Diesel Oil ROB departure.
   Fuel Oil Low Sulphur remaining on board	Updates Fuel Oil Low Sulphur ROB departure.
   Diesel Oil Low Sulphur remaining on board	Updates Diesel Oil Low Sulphur ROB departure.
   Fresh Water remaining on board	Inserted to position report.
   Bunkered Fuel Oil Input exact figure according to the BDR	Updates Fuel Oil bunkered for departure port call.
   Bunkered Fuel Oil Low Sulphur Input exact figure according to the BDR	Updates Fuel Oil Low Sulphur bunkered for departure port call.
   Bunkered Diesel Oil Input exact figure according to the BDR	Updates Diesel Oil bunkered for departure port call.
   Bunkered Diesel Oil Low Sulphur Input exact figure according to the BDR	Updates Diesel Oil Low Sulphur bunkered for departure port call.
   Remark	Inserted as remark to position report.

Top

Straits

Three straits may appear in the Dataloy VMS schedule: Torres, Bosporus and Maggelan. These will appear because expenses may arise. Dataloy Vessel Reporting do not consider these straits but moves to the next port call. Vessels should therefore report the port following the Torres, Bosporus and Maggelan straits. 

Top

Report Generator

The Report Generator collects necessary master data and customer specific fields to avoid the need for manual changes and/or having one report version/customer.
     1.  Master Data
     2.  Customer Specific Fields
 

...

To view and test available test report: Download and unzip the file to start testing the report:dataloy_vessel_report.zipdataloy_offline_test_report.zip.
Note: Data will not be updated in Dataloy VMS before the server is configured to receive vessel reports.

...